Search

[...]Access door for buildings in the field of potable water supply and wastewater disposal with average security requirements Door, ready for installation, double door, double skinned, completely made from 1.4307 stainless steel (AISI 304 L), with double rubber seal. The door leaves and frame closing flush, the fixable and swing leaf opening to the outside (in escape direction). Door leaves, skin: 1 mm , 55 mm thick, with injected CFCs-free polyurethane hard foam insulation, longitudinally ground surface finish, with rubber seal. Fastened to the frame with stable maintenance-free hinge plates. Mortise dead lock according to DIN 18251, class 3, with increased corrosion protection, stainless steel forend, provided for a customer-provided profile double cylinder (mechanical or digital), handle and cover of stainless steel. The fixable leaf is operated by means of a sliding locking bolt. The contact surface between the opening leaf and fixable leaf is rubber sealed. Frame, three-sided , fabricated from special section, with inserted rubber seal, with selectable sill closure, including fixing material. Options Frame: Z-frame Block frame Mounting: Embedded Bolted with dowelling clips Bolted through the frame (not to affect the finished wall) Door opening options: Hinges on left Hinges on right Sill closure: With step flashing Without step flashing Other Options: 1.4404 (AISI 316 L) stainless steel Panic lock Upper door closer, lockable in position One-part or two-part door arrestor Surface finish (lacquer with or without anti-graffiti properties, copper covering, wooden panelling) Electronic monitoring options (alarm system in door surface, magnetic contact, lock-bolt contact, block lock) Door heating (heating cable in frame and/or door surface), without temperature sensor, without controls Potential equalisation on frame Security ventilation louvres, openings to admit light Steel sheet finish for exterior door surface for installations exposed to sunlight[...]

[...]Access door for water chambers, ready for installation, single door, double skinned Completely made from 1.4404 stainless steel (AISI 316 L), with double rubber seal. The door and frame closing flush, the door opening to the outside (in escape direction). Door leaf, skin: 1 mm , 55 mm thick, with injected CFCs-free polyurethane hard foam insulation, longitudinally ground surface finish, door seal certified to KTW and DVGW W270 standards. Fastened to the frame with stable maintenance-free hinge plates. Mortise dead lock completely made from stainless steel according to DIN 18251, class 3, provided for a customer-provided profile half cylinder, lockable only from the dry side. Stainless steel door handle set with button outside and handle inside. Frame, three-sided , fabricated from special section, with inserted frame seal certified to KTW and DVGW W270 standards, selectable sill closure, including fixing material. Frame and door shielded arc-welded and acid bath cleaned before washing, drying and surface passivation. Options Frame: Z-frame Block frame Mounting: Embedded Bolted with dowelling clips Bolted through the frame (not to affect the finished wall) Door opening options: Hinges on left Hinges on right Sill closure: With step flashing Circumferential block frame on four sides Other Options: Upper door closer, lockable in position (mounted on the dry side) One-part or two-part door arrestor Electronic monitoring options (alarm system in door surface, magnetic contact, lock-bolt contact, block lock) Potential equalisation on frame (dry side)[...]

[...]Access door for buildings in the field of potable water supply and wastewater disposal with average security requirements. Door, ready for installation , single door, double skinned, completely made from 1.4307 (AISI 304 L) stainless steel, with double rubber seal, the door and frame closing flush, the door opening to the outside (in escape direction). Door leaf , skin: 1 mm, 55 mm thick, with injected CFCs-free polyurethane hard foam insulation, longitudinally ground surface finish, with rubber seal. Fastened to the frame with stable maintenance-free hinge plates. Mortise dead lock according to DIN 18251, class 3, with increased corrosion protection, stainless steel forend, provided for a customer-provided profile double cylinder (mechanical or digital), handle and cover of stainless steel. Frame, three-sided , fabricated from special section, with inserted rubber seal, with selectable sill closure, including fixing material. Frame and door shielded arc-welded and acid bath cleaned before washing, drying and surface passivation. Options Frame: Z-frame Block frame Mounting: Embedded Bolted with dowelling clips Bolted through the frame (not to affect the finished wall) Door opening options: Hinges on left Hinges on right Sill closure: With step flashing Without step flashing Other Options : 1.4404 (AISI 316 L) stainless steel Panic lock Upper door closer, lockable in position One-part or two-part door arrestor Surface finish (lacquer with or without anti-graffiti properties, wooden panelling) Electronic monitoring options (alarm system in door surface, magnetic contact, lock-bolt contact) Door heating (heating cable in frame and/or door surface), without temperature sensor, without controls Potential equalisation on frame Security ventilation louvres, openings to admit light Steel sheet finish for exterior door If the door is exposed to sunlight, its operability may be affected. In such a case, it is recommended to equip the door outside with a wood panelling or steel sheet.[...]

[...]Single-beam entrance aid, with design certification in accordance with DIN 19572 Made of 1.4404 (AISI 316 L) stainless steel. Available as either a removable and portable or as stationary collapsible unit. Consisting of a handle and guide. Guide with two holes, diameter: 12 mm, for bolted fixing to the wall of the manhole. With a possibility of adjustment for the handle. Handle of distortion-free pipe, 33.7 x 3.6 mm, total length: 1500 mm. Completely shielded arc welded, acid-treated in a pickling bath and passivated. Optionally available in: Stainless steel fixing material: stud anchors Special design: Suitable for ‘econorm’ manholes, wall distance to beginning of insertion opening: 158 mm[...]

[...]Access door for buildings in the field of potable water supply equipped with a burglar alarm system Security door, burglar and attack proof , certified to security of DIN EN 1627, resistance class RC3, ready for installation, double skinned, completely made from 1.4307 stainless steel (AISI 304 L), with double rubber seal, the door and frame closing flush, the door opening to the outside (in escape direction). Sound insulation: 34/29 dB . Security class RC3 is recommended by the criminal investigation department if the building is additionally secured by means of a burglar alarm system. Door leaf with injected CFCs-free polyurethane hard foam insulation, longitudinally ground surface finish, with rubber seal. Fastened to the frame with stable maintenance-free hinge plates. The closed door engaging flush with the frame by means of solid anchor bolts engaging in the frame for four-point locking. Galvanized safety lock with stainless steel forend, with austenitic manganese steel plate as anti-drilling protection, provided for a customer-provided mechanical profile half cylinder in accordance with DIN 18252:2006-12,21-,31-,71-BZ), with anti-panic lock, i.e. the door can any time be opened from inside by operating the handle, even when locked. Protective stainless steel fitting, without cylinder cover, with a rigidly mounted turning handle and a red plastic handle inside. Frame, three-sided , fabricated from special section, with inserted rubber seal, with step flashing, including fixing material. Frame and door shielded arc-welded and acid bath cleaned before washing, drying and surface passivation. Options 1.4404 (AISI 316 L) stainless steel One/two security ventilation louvre(s) size 500 x 300 mm Provided for a customer-supplied digital profile cylinder with anti-panic function and pulling protection Upper door closer, lockable in position One-part or two-part door arrestor Lowerable floor seal Lockable from inside with a second handle Surface finish (lacquer with or without anti-graffiti properties, copper covering, wooden panelling) Electronic monitoring options (alarm system in door surface, magnetic contact, lock-bolt contact) Door heating (heating cable in frame and/or door surface), without temperature sensor, without controls Lock for two side-by-side profile cylinders (that can be opened independently) Stainless steel rain protection rosette for the stainless steel profile cylinder Block frame insulation Potential equalisation on frame Steel sheet finish for exterior door surface for installations exposed to sunlight Frame / mounting Options: Z-frame – bolted with dowelling clips Block frame – bolted with dowelling clips Block frame – bolted through the frame Door opening Options: Hinges on left Hinges on right Note: If the door is exposed to sunlight, its operability may be affected. In such a case, it is recommended to equip the door outside with a wood panelling or steel sheet.[...]

[...]Access door for buildings in the field of potable water supply equipped with a burglar alarm system Security door, burglar and attack proof, certified to security of DIN EN 1627, resistance class RC3, ready for installation, double skinned, completely made from 1.4307 (AISI 304 L) stainless steel, with double rubber seal, the door leaves and frame closing flush, the fixable and swing leaf opening to the outside (in escape direction). Door leaves with injected CFCs-free polyurethane hard foam insulation, longitudinally ground surface finish, with rubber seal. Fastened to the frame with stable maintenance-free hinge plates. The closed door leaves engage flush with the frame by means of solid anchor bolts engaging in the frame for four-point locking. Galvanized safety lock with stainless steel forend, with austenitic manganese steel plate as anti-drilling protection, provided for a customer-provided mechanical profile half cylinder in accordance with DIN 18252:2006-12,21-,31-,71-BZ), with anti-panic lock, i.e. the door can any time be opened from inside by operating the handle, even when locked. Protective stainless steel fitting, without cylinder cover, with a rigidly mounted turning handle and a red plastic handle inside. The fixable leaf is operated by means of a sliding locking bolt. The contact surface between the opening leaf and fixable leaf is rubber sealed. Frame, three-sided , fabricated from special section, with inserted rubber seal, with step flashing, including fixing material. Frame and door shielded arc-welded and acid bath cleaned before washing, drying and surface passivation. Options 1.4404 (AISI 316 L) stainless steel One/two security ventilation louvre(s) size 500 x 300 mm Provided for a customer-supplied digital profile cylinder with anti-panic function and pulling protection Upper door closer, lockable in position One-part or two-part door arrestor Lowerable floor seal Lockable from inside with a second handle Surface finish (lacquer with or without anti-graffiti properties, copper covering, wooden panelling) Electronic monitoring options (alarm system in door surface, magnetic contact, lock-bolt contact, block lock) Door heating (heating cable in frame and/or door surface), without temperature sensor, without controls Lock for two side-by-side profile cylinders (that can be opened independently) Stainless steel rain protection rosette for the stainless steel profile cylinder Block frame insulation Potential equalisation on frame Steel sheet finish for exterior door surface for installations exposed to sunlight Frame / mounting: Z-frame – bolted with dowelling clips Block frame – bolted with dowelling clips Block frame – bolted through the frame Door opening options: Hinges on left Hinges on right Note: If the door is exposed to sunlight, its operability may be affected. In such a case, it is recommended to equip the door outside with a wood panelling or steel sheet.[...]

[...]Access door for buildings in the field of potable water supply without a burglar alarm system Security class RC4 is recommended by the criminal investigation department if the building is not secured by means of a burglar alarm system. Security door, burglar and attack proof , certified to security of DIN EN 1627, resistance class RC4, ready for installation, single-leaf, double skinned, completely made from 1.4307 stainless steel (AISI 304 L), with double rubber seal, the door and frame closing flush, the door opening to the outside (in escape direction). Sound insulation: 34/29 dB. Door leaf with injected CFCs-free polyurethane hard foam insulation, longitudinally ground surface finish, with rubber seal. Fastened to the frame with stable maintenance-free hinge plates. The closed door engaging flush with the frame by means of solid anchor bolts engaging in the frame for four-point locking. Additional protection of the internal lock box through an attack-proof protecting plate with anti-panic function. Galvanized safety lock with stainless steel forend, with austenitic manganese steel plate as anti-drilling protection, provided for a customer-provided mechanical profile half cylinder in accordance with DIN 18252:2006-12 42-,82-BZ, with anti-panic lock, i.e. the door can any time be opened from inside by operating the handle, even when locked. Protective stainless steel fitting, with cylinder cover, with a rigidly mounted turning handle on the stainless steel outside cover and a red plastic handle inside. Frame, three-sided as block frame , with inserted rubber seal, with step flashing, including fixing material. Frame and door shielded arc-welded and acid bath cleaned before washing, drying and surface passivation. Options 1.4404 (AISI 316 L) stainless steel One/two security ventilation louvre(s) size 400 x 200 mm Provided for a customer-supplied digital profile cylinder Upper door closer, lockable in position One-part or two-part door arrestor Lowerable floor seal Lockable from inside with a second handle Surface finish (lacquer with or without anti-graffiti properties, wooden panelling) Electronic monitoring options (alarm system in door surface, magnetic contact, lock-bolt contact) Door heating (heating cable in frame and/or door surface), without temperature sensor, without controls Lock for two side-by-side profile cylinders (that can be opened independently) Block frame insulation Potential equalisation on frame Steel sheet finish for exterior door surface for installations exposed to sunlight Mounting: Bolted with dowelling clips Bolted through the frame Door opening options: Hinges on left Hinges on right Note: If the door is exposed to sunlight, its operability may be affected. In such a case, it is recommended to equip the door outside with a wood panelling or steel sheet.[...]

[...]Access door for containers, especially in the field of potable water supply, pressure-tight up to a water gauge of 10 m Pressure-tight door , pressure-tight up to a water gauge of 10 m, opening to the pressure side, ready for installation, to be lined on both sides (wall thickness ≥ 280 mm), rectangular, completely made from 1.4404 (AISI 316 L) stainless steel, statically certified. Door, 5 mm thick , reinforced with U-shaped bent plate. Smooth door leaf on the pressure side. With circumferential square silicone seal, suitable for potable water, ozone resistant, certified to KTW and DVGW W 270 standards. Locking levers operable both from the door outside and, for safety reasons, also from the pressure side while the reservoir is empty. With stable maintenance-free hinge plates between the door and frame. Frame , circumferential with one centre and two side gaskets, provided for embedding in concrete. Frame with lifting eyes. Frame and door shielded arc-welded and acid bath cleaned before washing, drying and surface passivation. Door opening variants: Hinges on left Hinges on right Options Frame, for retrofitting, space required for the frame: 150 mm, circumferential. Prerequisite is a plane inner wall surface, tolerance: ± 1 mm per metre Pressure door for round tanks Centrally installed inspection window, inside diameter: 150 mm, with or without window wiper Installed LED underwater spotlight Installed cylinder lock (operable from one side) Locking by means of screw caps Pressure door with three-sided open-top frame for parapets, maximum water gauge = door height. Sanding of frame parts in contact with concrete Condensate drain on external door surface Doorstop with wedge Sampling valve on external door surface Partly submersible, lower part pressure-tight, upper part with an integrated inspection opening Provided for welding to the PE coating Potential equalisation on the frame Completely made of 1.4307 (AISI 304 L) stainless steel[...]

[...]Collapsible hand post with double handle, with design certification in accordance with DIN 19572 Made of 1.4307 (AISI 304 L) stainless steel, for safety access ladders with 300 mm, 400 mm, 500 mm width, for ladder lengths from 2010 mm. Overall length: 1800 mm. Entrance aid in accordance with DIN 19572. Access ladders must have a handhold at their exit. This requirement is deemed to be fulfilled if one or both handles of a ladder project at least 1.1 m beyond the exit height. Completely shielded arc welded, acid-treated in a pickling bath and passivated. Optionally available in: 1.4404 (AISI 316 L) stainless steel[...]

[...]Manhole cover, installed flush with the surface for pedestrian and/or vehicle traffic, optionally in class A15 or B125, D400 or E600. Weatherproof, odour-tight against pressureless water, attack-proof, round in shape, made of 1.4307 (AISI 304 L) stainless steel. The cover consists of a stainless steel tear pattern plate, with additional bracing on the bottom according to the weight (load class), slip resistance in accordance with DIN EN 124-1:2015-09, with a low-wear seal on the cover bottom side, screw lock, including lock system with anti-drilling protection, as standard with hardened safety lock as recommended by criminal investigation departments and in accordance with the normative standards; the profile cylinder in accordance with DIN 18252 to be provided by the customer. Frost-proof inner hinges, help for opening in the form of stainless steel gas assisted spring dampers with integrated cover arrestor which can only be undone by hand. A connection for potential equalisation is provided. Easy-to-install encasing frame, standard height 250 mm, with external wall clamps, provided for embedding in concrete (concrete up to upper frame edge) and for fixing to the casing. Manhole cover and frame shielded arc-welded, acid-treated in a pickling bath and passivated. Operating key included. Designed for Installed flush with the surface for pedestrian and/or vehicle traffic, optionally in class A15, B125, D400 or E600, weatherproof, odour-tight against pressureless water, attack-proof, round in shape, made of 1.4307 (AISI 304 L) stainless steel. Secure to prevent forced access , certified to resistance class RC3 according to DIN EN 1627 in class D400, meeting the requirements of DVGW W 1050 - Object protection for water supply structures. Suitable for use in Ex zone 1. Not suitable for big-volume traffic (see definition below at the Download section). Designed for a clear width up to and including 1000 mm and certified to: DIN 1229 / DIN EN 124-1:2015-09 and DIN EN 124-3:2015-09, classes A15, B125, D400, E600 with test certificate and external monitoring. Designed for a clear width bigger than 1000 mm and statically calculated according to: DIN EN 1991:2010-12 (Eurocode 1) and DIN EN 1993:2010-12 (Eurocode 3), class EC10 (Pedestrian traffic) and EC100 (Stationary vehicle traffic) Options 1.4404 (AISI 316 L) stainless steel Lift-off cover (without spring dampers and hinges) Non-standard sizes Encasing frame, non-standard installation height Designed for dowelling (only possible for class A15) Possibility to open the cover from below, the traffic situation to be taken into account Multi-part cover Suitable for big-volume traffic up to a maximum surface of 1 m² (no emergency exit possible). See definition for big-volume traffic below at the Download section. Magnetic contact Cover insulation One-part covers watertight up to 5m WC (class D400 only) One-part covers back-water proof up to 5m WC (class D400 only) Safety guard / antifall guard[...]